Bad mini

BAD HORSE OVERDRIVE PEDALE BAD HORSE - Mini Series - Overdrive per chitarra - Controlli: Volume + Gain + Tone - L'Onerdrive pib'/xc3/xb9' famoso e eccessivamente caro al mondo, replicato alla perfezione in un pedale piccolo di statura ma dal grande suono - Switch: On/Off true bypass - Alimentazione: 9V - Assorbimento: 10mA - Dimensioni: 9,2x3,7x3,2cm - Peso: 266g.

Satellite finder Misuratore di Segnale Analogico per Direct TV SAT Accord Mini satellite finder Misuratore di Segnale Analogico per Direct TV SAT Orientamento Parabola Strumento di grande precisione per l'orientamento della parabola e la ricezione del segnale televisivo migliore Si tratta di un satfinder (trovatore di satelliti) controllato da un microprocessore ad alta tecnologia, che lo rende molto affidabile ed accurato La forza del segnale è presentata graficamente sul display LCD retro-illuminato. Ã^ molto sensibile e può individuare il più debole dei segnali. Frequenza 950-2150Mhz Looking for a same functional and performance with SF-9502, the price is much lower satellite finder ? Then this is your ideal stuff. Band 22K and H / V indicator is to satellite finder weapon, With their installation stars it becomes easy Features: Online IF signal strength meter excellent sensitivity, DC can pass to LNB and internal light, Built 0/22KHz 13/18V LED and buzzer Elegant appearance, easy to carry Input Frequency: 950-2150MHz / Supply voltage: 13-18V DC Maximum input level: -10dBm Minimum input level: -40dBm Learn ABC Communications Satellite Finder SF-95 to use 1, the satellite finder satellite receiver connected to the LNB on the antenna between. 2, adjusting satellite finder on the front panel knob, pointer on the dial "5" position. 3, adjusting the antenna azimuth and elevation, while satellite finder to the maximum angle of deflection of the pointer, the front panel adjustment knob counterclockwise, so that the part of the received signal attenuation, and then adjust the antenna azimuth, elevation and the LNB polarization angle, until the satellite finder until the pointer is no longer increasing. 4, with the satellite receiver determines whether the signal is the desired satellite signal. If it is, remove the finder device, the receiver can be connected with the LNB again; if the received signal is not the desired satellite signal, repeat the above work. Common phenomenon 1 - satellite finder pointer refers to the maximum point, but there is no signal. Because satellite finder signal received by the antenna direction only preliminary judge whether there is a star, rather than the desired signal is directly displayed on the satellite finder on the dial, it's just looking out signals an auxiliary device. 2 - In the case where the antenna is not adjusted, the pointer always refers to the maximum point. Check that the antenna is facing the front or the front of the building is blocked, if there is no such phenomenon exists, indicating that at this time LNB gain is too large, need to lose satellite finder signal attenuation part. Learn SF-95 satellite finder to use A cable. Instruments. TV antenna connection Operation 1 - The satellite finder side labeled "TO LNB" connected to the antenna tuner at the other side labeled "TO REC" is connected to the receiver, and the receiver and the TV turned on. 2 - receiver is turned on, the receiver out of the voltage supply 13-18V, check whether there is satellite finder lights, lights indicate satellite finder is working properly. 3 - Set the receiver in satellite data to be received. (Including local oscillator frequency, downlink frequency, symbol rate, polarization, etc.) and open to signal strength, signal quality cursor state. B finder dashboard Operation: 1 satellite finder attenuator spiral configuration, is to adjust the signal attenuation of the size of the receiver is powered, operable screw attenuator control the pointer on the scale in Table 5 grid, satellite finder will issue a faint sound, this time, a slight shake antenna near you looking for stars, satellite finder found out signal is input, the sound will increase, the pointer will also rise between cells table 8-10 scale or higher, indicating a star signal input. At this point the receiver signal quality combined with the cursor to see if what you're looking for stars. 2 satellite finder does not recognize the user to find the star signal, where there are star signal input, satellite finder always show a signal. At this time only to find out from the star receiver input signal quality parameter the cursor up to confirm. 3. Ku-band can be directly connected, C-band tune out when you need satellite finder to LNB between the string into a power splitter cable or 100 meters, in order to attenuate the signal, or satellite finder is a result of self-excited hands can not come down. 4 between the tall buildings or strong interference zone for stars, satellite finder will lead to self-excited whistle and hands can not come down. C if satellite finder signal is received and the digital machine failed to show a signal when the following situations 1 user is not looking out signals. 2 LNB polarization. Focal placement errors need to be adjusted. 3 signal is weak, turn the pointer through the bad parts is transferred between 4-5, re-adjust the antenna or LNB, the signal again increases. 4 satellite finder pointer refers to the maximum point, but there is no signal. Because satellite finder signal received by the antenna direction only preliminary judge whether there is a star, rather than the desired signal is directly displayed on the satellite finder on the dial, it's just looking out signals an auxiliary device. 5, in the case where the antenna is not adjusted, the pointer is always the maximum at the finger. Check that the antenna is facing the front or the front of the building is blocked, if there is no such phenomenon exists, indicating that at this time LNB gain is too large, need to lose satellite finder signal attenuation part