Cc3d flight controller 8pin

Elenco delle migliori vendite cc3d flight controller 8pin

BETAFPV F405 2-4S AIO 20A V4 TOOTHPICK BRUSHLESS FLIGHT CONTROLLER NO RX BLHELI_32 20A ESC FOR BETA95X V3 WHOOP DRONE 2-4S MOTOR

【F405 Chip】The flight controller has been updated to F405, can totally handle 20A continuous current(22A burst), gives pilots a powerful flight. BETAFPV 12A/20A AIO flight controller will unify the UART, which is convenient for pilots to solder
【Pluggable Connector】BETAFPV F405 AIO 20A flight controller integrated digital VTX connector and receiver connector, just plug and play, which is convenient for installation
【Compatible Motors】F405 AIO 20A FC is compatible with 110X/120X/140X series motors, pilots can build a bigger quad with this powerful FC to save weight
【Suitable Drones】Comes with a 26mm x 26mm whoop mounting pattern, this board can be added to both the toothpick drone and the cinematic whoop quadcopter like Beta95X V3 and Beta95X V3 HD Digital VTX
【Support Receiver】Built without receiver, supports Frsky XM/XM+/ Futaba/ Flysky /TBS Crossfire/ DSMX receiver. Please note: when you connect the external receiver, the pads near the RX connector need to be soldered. Refer to the 6th picture

[Di più]

Vedi prezzi in Amazon

BETAFPV F4 AIO 1S BRUSHLESS FLIGHT CONTROLLER SPI FRSKY LBT RECEIVER 5A ESC INTEGRATED VTX WITH BT2.0 CONNECTOR FOR 1S FPV BRUSHLESS WHOOP DRONE LIKE METEOR65 HX100 SE QUADCOPTER

【Compatible Drone】This newest F4 AIO 1S brushless flight controller comes with F411 chip, it is specially designed for 1S brushless whoop drone like Meteor65, HX100 SE
【Integrated 25mW VTX】BETAFPV newest F4 AIO 1S brushless flight controller integrated 25mW VTX, no need to solder an external VTX, more convenient for installation and it saves the weight of the weight-sensitive whoop drone like Meteor65
【Plug&Play Connector for Camera】Come with a 3-pin connector for connecting C01 micro camera and 6-pin connector for Nano HD camera directly, no soldering needed, it is convenient for installation, just plug and play
【Frsky Receiver】BETAFPV F4 AIO 1S brushless flight controller comes with an SPI Frsky receiver, it pre-flash to LBT protocol in default. It supports to change its protocol from LBT to FCC if your transmitter is FCC, more detail please contact us
【RGB LEDs】Increased two RGB LEDs on this newest F4 AIO 1S brushless FC to make your drone looks dazzled. Any other technical needed just feel free to contact: support03@betafpv.com

[Di più]

Vedi prezzi in Amazon

BETAFPV F4 FC BRUSHED FLIGHT CONTROLLER WITH SPI FRSKY RECEIVER BETAFLIGHT OSD SMART AUDIO FOR TINY WHOOP MICRO RACING DRONE

The default configuration from factory is Frsky D16 mode (FRSKY_X). Built in Frsky receiver is compatible with Taranis, Taranis Plus, X9E, Horus X12S, XJT Modules. In Betaflight Configuration, it should be setted as FRSKY_D receiver (aka Frsky D8 mode) or FRSKY_X receiver (aka Frsky D16 mode) in SPI RX mode.
This is a SPI Frsky receiver. Binding easier than before, no need to click the bind button when power on. Manual: https://betafpv.freshdesk.com/support/solutions/articles/27000021366-how-to-bind-your-radio-transmitter-brushed-fc-board
The flight controller board comes pre-flashed with Betaflight firmware, and pre-soldered 55mm power cable pigtail with JST-PH 2.0 connector, AKA PowerWhoop connector. Designed to work with current Tiny Whoop or Blade Inductrix setups
F411 Processor can reach to 100MHz, much faster than the F3 Flight Controller with 72Mhz. Integrated with Frsky receiver only. Upgraded to 30A Lower Resistance MOSFET, Firmware version: betaflight_matekf411rx_3.4.0. Built-in BetaFlight OSD (STM32 controls OSD chip over SPI in DMA mode). Support Smart Audio.
Some basic guidance and typical FAQ, please check it here : https://betafpv.freshdesk.com/support/solutions

[Di più]

Vedi prezzi in Amazon

Holybro kakute f4 v2.4 flight controller 30.5x30.5mm 2-8s mpu6000 osd con uscita bec 5v 9v supporto per unità dji o3 air

Italia

Descrizione:Il flight controller Holybro Kakute F4 V2.4 include una porta plug-and-play per la telecamera DJI O3 HD, porte ESC 4in1, barometro, OSD, 5 UART, capacità di registrazione con flash integrata, BEC 5V e 9V/3A, layout per una facile saldatura e molto altro.Il Kakute F4 V2.4 è pronto per l'HD DJI. Ha una porta plug-and-play facile da usare con un regolatore integrato 9V/A progettato per alimentare il tuo trasmettitore video HD come DJI O3 Air Unit9V/3A (Ottimizzato per l'unità DJI O3 Air) 7x uscite PWM (6 uscite per i motori, 1 per LED)Supporta ricevitori seriali (SBUS, iBus, Spektrum, TBS CRSF, ESLR).Foro di montaggio: 30,5x30,5 mm, foro Φ4 mm con guarnizioni M3Dimensione: 37x37mmPeso: 7gPorta JST-SH1.0_8pin (Per ESC 4in1)Porta JST-SH1.0_6pin (per sistema DJI/Caddx HD e altri VTX) La confezione include:1xKakute F4 V2.44x Spina in Gomma Antivibrazione al Silicone *41x cavo JST SH 6pin a JST GHR 8pin da 80mm e 150mm (per sistema DJI/Caddx HD)1x cavo JST SH a 6 pin da 100mm (per sistemi Caddx HD)1x cavo JST SH a 8 pin 100mm (per ESC)

39,15 €

Vista prodotto

Holybro flight controller kakute h7 v1 e stack esc tekko32 f4 4in1 50a di 30.5x30.5mm per droni da corsa fpv rc

Italia

Specificazione:Marca: HolybroModello: stack Kakute H7 V1Flight Controller Kakute H7 V1(Manuale)MCU: processore STM32H743 a 32 bit che funziona a 480 MHzIMU: MPU6000Barometro: BMP280OSD: AT7456EChip Bluetooth integrato: ESP32-C3Compatibile con l'app SpeedyBee per IOS e Android Nota: Il Bluetooth a bordo è impostato per spegnersi automaticamente quando il controllore di volo è sbloccato (armato) si attiva automaticamente quando il controllore di volo è bloccato (disarmato).6x UARTs (1,2,3,4,6,7; UART2 viene utilizzato per la telemetria Bluetooth)9x Uscite PWM (8 uscite motore, 1 LED)Porta 2x JST-SH1.0_8pin (compatibile con ESC 4 in 1, compatibile con X8/Octocopter)1x porta JST-GH1.25_6pin (per sistema HD come Caddx Vista e Air Unit)Tensione di ingresso della batteria: da 7V a 42VBEC 5V 2A Cont.BEC 9V 3A Cont. (Aggiornato)Foro di montaggio: 30,5 x 30,5 mm / foro da Φ4mm con guarnizioni da Φ3mmDimensione: 35x35mmPeso: 8gFirmware di destinazione: BetaFlight: KakuteH7 (v4.2.11 e superiori)INAV: Aggiunto supporto per scheda SD in KakuteH7 (4.0.0 e superiore) nella versione 4.1.0.ArduPilot: KakuteH7 (4.2.0 e successivi)Tekko32 F4 4in1 50A ESC(Istruzioni per spille)Corrente continua: 50A x4Corrente di picco: 60A x4Supporta batterie 4-6SSupporta DShot 150/300/600/1200 e MultiShot/OneShot/Proshot/PWM, ecc.Telemetria ESC supportataSensore di corrente analogico a bordoNessuna uscita BECfirmware BLHeli_32Condensatore da 1000uf 35v incluso (altamente consigliato per impostazioni 6s)Rappor

174,71 €

Vista prodotto

Altri prodotti di casa e giardino simili a cc3d flight controller 8pin

cc3d flight controller cc3d flight flight controller mamba f405 flight controller cc3d 8pin flight flight case consolle flight case cdj mixer flight case pioneer flight case mixer flight simulator flight case consolle dj flight case pioneer dj flight case rockbag flight case cdj pioneer flight case casse flight case completo flight case custodia flight case custodia x flight case x mixer flight case usato flight case effetti flight case flight case misura