Dbx frequency response

Channels: 2 Input sensitivity: 300mV (7V max) Noise reduction system: dbx II S/N improvement: 40dB Dynamic range: 100dB Frequency response: 20Hz to 20kHz Signal to noise ratio: 85dB Total harmonic distortion: 0.1% Dimensions: 440 x 44 x 190mm Pedizioni in tutto il mondo Valutiamo permute

• 4 Band Stereo Gating, Compression and Limiting • 5 Band Parametric EQ with either an adaptive Q or a constant Q response • Hi and Low shelves w/switchable slopes 3, 4.5, 6, 9, and 12 dB/octave • EQ can be positioned pre dynamics, or post dynamics • 5 Band Parametric Side Chain EQ with either an adaptive Q or a constant Q response • Dual Mono or True Stereo Operation with True RMS Power Summingâ„¢ • TYPE IVâ„¢ Conversion System with TSEâ„¢ Tape Saturation Emulation • Normalizer â€â€œ flexible gain optimization • Stereo adjust â€â€œ increased control of stereo imaging • Dither outputs to 8,16, 20, or 24 bits, and noise shaping • Sample rate conversion • Sync input/output using dbxâ€â„¢s own proprietary clock chips for extremely low jitter sync

Equalizzatore originale americano, 110 volt Frequency Response: 20Hz to 20,000Hz +/- 0.5dB Hum and Noise: 90dB (79uV) below 2.5V flat response. 85dB (140uV) below 2.5V worst case. Harmonic and Intermodulation Distortion: less than 0.02% at 2.5V output 20Hz to 20,000Hz Low frequency Compensation: Variable from 0 to +17dB at 20Hz Input Sensitivity: 2.5V into 27k ohms for rated output with controls set for flat response High Frequency Compensation: Variable +/-10dB at 20,000Hz Output Level and Impedance: 2.5V into 10k ohms or more with the output level at zero and all other controls set for flat response. Programmable Filters: 14 sections (7 per channel) each of which can be programmed for standard 1/3 octave center frequencies from 20Hz to 1000Hz. Filter bandwidth is programmable for narrow (approx. 1/3 octave) or wide (approx. 1 octave). Amplitude is continuously adjustable +/- 12dB for narrow and +/-15 dB for wide. A detented control is used to position for flat response. Programming is achieved by means of plug-in capacitors provided with the MQ107. Size: 3-1/2" high, 5-3/4" wide and 14" long Finish: Chrome and black Weight 7 lbs. 9 oz.

The product is new, has only been opened and tested and is fully functional. Il prodotto è nuovo, è stato solamente aperto e provato ed è perfettamente funzionante. DUAL CHANNEL UHF WIRELESS BELT-PACK MICROPHONE SYSTEM EIKONâ€â„¢s WM101 V2 series is a complete range of single or dual channel wireless products with handheld transmitters or bodypack transmitters with headset microphone.This line of products offers a particularly interesting value for money, thanks to the quality capsule of the transmitters and the Digital Encrypting system with 3 available channels.Single-channel systems include a rugged ABS housing while dual-channel systems include a solid metal chassis. Fixed dual frequency wireless microphone system Encrypted Digital Audio 863 â€â€œ 865 Mhz frequency range 30 meter/ 100 feet range 50 Hz -15 KHz frequency response Condenser headset with cardioid capsule Low-profile metal desktop receiver with two foldable antennas TECHNICAL SPECIFICATIONS RECEIVER Receiver Type. UHF Band Frequency Range: 863-865 MHz RF Frequency Stability: ±0.002 % RF Image/Spurious Rej.: > 70 dB RF Interference Reject.: > 70 dB RF Sensibility: -105 dBm Frequency Response: 50 – 15000 Hz Modulation Method: PCM Digital 24 bit THD Distortion: 90 dB S/N Ratio >: 100 dB Power Requirement: 12 V DC / 500 mA Output Connector: Unbalanced ¼ “ jack Dimensions (mm): H 45 x L 150 x W 118 BELT-PACK TRANSMITTER Carrier Frequency Range: UHF: 863-865 MHz Modulation method: FM (F3E) Transmitting Power:

Bellissimo sistema yamaha, le foto purtroppo accentuano le ditate sul frontale nero e lo sviliscono un po', dal vivo molto megio. L'equalizzatore a 10 bande è davvero un pezzo eccezionale a livello funzionale ed anche estetico con tutti i suoi led rossi. Il sistema è uniproprietario sempre tenuto in un mobiletto (disponibile e in regalo per cui prende tutto il sistema). Nessun pezzo presenta righe, scalfitture o botte. Il sistema è composto da amplificatore A-520 equalizzatore GE-40 A-520 Power output: 75 watts per channel into 8Ω (stereo) Frequency response: 20Hz to 20kHz Total harmonic distortion: 0.01% Damping factor: 50 Input sensitivity: 0.16mV (MC), 2.5mV (MM), 150mV (line) Signal to noise ratio: 75dB (MC), 92dB (MM), 100dB (line) Channel separation: 55dB (MM), 55dB (line) Output: 150mV (line) Dimensions: 435 x 136 x 339mm Weight: 7.5kg GE-40 Input Sensitivity: 1V Output Level: 1V (7V max) Frequency response: 10Hz to 100kHz Signal to Noise Ratio: 110dB Total harmonic distortion: 0.005% Channel separation: 66dB Control Range: ± 15dB Frequency Bands: 30, 60, 120, 240, 480, 1K, 2K, 4K, 8K, 16KHz Dimensions: 435 x 112 x 275mm Weight: 3.7kg Ritiro a Torino, possibile ascolto. No scambio o permute. Possibile spedizione in Italia a 20 €. Non rispondo ad ancora disponibile. (abbinabile ad elettroniche come: accuphase, rotel, yamaha, denon, pioneer, kenwood, toshiba, sansui, technics, teac, mission, grundig, philips, nakamichi, panasonic international, esb, rcf, jbl, ar audio, sony, allison, jvc, harman kardon, wharfedale, akg, am audio, tivoli audio, cervin wega, cerwin vega, genesis, luxman, mcintosch, b&w, thorens, nad, lenco, klipsch, tannoy, akai, altec, marantz, outline pro, infinity, phase linear, arcam, bose, telefunken, fase, mcintosh, linn, proton, meridian, krell, cary, dared, cayin, rogers, audio note, pro-ject, celestion ditton, kef, coral, naim, quad, sonus.proac, spendor, leak, mark levinson, focal, bang olufsen, b&o, magnat, velodyne, bose, klh, jpw, jm lab, monster cable, van den hul, hi fi, hi end, high end, pre finale, stereo, shure, dac, convertitore, audio video, sintoamplificatore, integrato, valvole)

Buongiorno, con il presente annuncio, proponiamo 2 diffusori/monitor attivi DB TECHNOLOGIES FLEXSYS F10A, da 400 W RMS l’uno per un totale di 800 W. I diffusori sono stati solo testati in studio pochissime ore e mai utilizzati altrove. Versano in perfette condizioni estetiche e funzionali. Di seguito riportiamo le specifiche tecniche: Speaker Type 2-Way Active Speaker Dati acustici Frequency Response [-10dB] 70 - 20.000 Hz Frequency Response [+/- 3dB] 80 - 19.000 Hz Max SPL 125 dB HF 1 " Type HF Neodymium compression driver Directivity 90/40 x 60 ° Horn Asymmetrical CD Horn LF 10" Amplificatore Amp Technology Digipro® Amp Class Class D Power PRG 400 W Peak Power 800 W Processore Controller DSP 24bit/48kHz System Presets Flat, Processed Limiter Dual Active Peak, RMS, Thermal Crossover Frequency LF-HF 2050 Hz Slope MF-HF 24 dB/Octave Meccanica Box MDF Angles Up Monitor use 40° Width 300 mm (11.8 in) Height 480 mm (18.9 in) Depth 300 mm (11.8 in) Peso 12 kg (26.46 lbs) Piena disponibilità per qualsiasi informazione. Si valutano eventualmente permute, rigorosamente di persona. È possibile il ritiro di persona o la spedizione in tutta Europa. Metodi di pagamento accettati: PayPal, Bonifico Bancario, Contanti. Cordialmente, Colombo Audio Service

Vendo amplificatore per basso Mark Bass Mini CMD 151P "Custom" Dettagli tecnici sul sito Mark Bass - CUSTOMIZZAZIONE - L'amplificatore e' stato customizzato con queste modifiche: - Tweeter originale (piezo) sostituito con tweeter a ferrofluido Monacor HT-30 - Amplificatori operazionali del preampli (originali: TL072, 0.32 EUR/chip) sostituiti con OPA1642 (SoundPlus Series, 1.91 EUR/chip) - Condensatori elettrolitici del preampli (segnale e alimentazione) sostituiti con componenti a basso ESR / 105 gradi - Jack input, send e return, uscita cassa sostituiti con jack professionali Neutrik - Ventolina raffreddamento sostituita con una a bassa rumorosita' Rispetto all'ampli non customizzato, il suono e' molto piu' definito e dinamico e non presenta piu' quegli alti taglienti enfatizzati dal tweeter piezo originale. Il rumore di fondo (hiss) e' diventato praticamente inesistente. - CONDIZIONI - L'amplificatore e' stato COMPLETAMENTE REVISIONATO (spolverato, pulito, disossidato e testato) a gennaio 2020 Woofer in condizioni perfette (vedi foto) L'unico difetto e' la moquette originale che si e' parzialmente staccata su un lato (vedi foto), dovuta alle centinaia di concerti che ha fatto (visto che suona bene!) Qualsiasi prova a casa mia, se volete portatevi il vostro basso per provarlo per bene Fornisco insieme all'ampli il manuale, il cavo corrente e il tweeter piezo + resistenza originali Non faccio spedizione visto l'ingombro / peso, solo ritiro a mano "visto e piaciuto" INPUTS - INPUT: impedance 500 kOhm, max. voltage 15 Vpp BALANCED INPUT (XLR): impedance 22 kOhm, max. voltage 25 Vpp EFFECT RETURN: impedance 22 kOhm, max. voltage 25 Vpp FREQUENCY RESPONSE: 40 Hz to 18 kHz CONTROLS - GAIN: -80 dB to +23 dB range MASTER VOLUME GROUND LIFT (switch on rear panel) EQUALIZATION - LOW: center frequency: 40 Hz; level: ±16 dB LOW MID: center frequency: 360 Hz, level: ±16 dB HIGH MID: center frequency: 800 Hz, level: ±16 dB HIGH: center frequency: 10 kHz, level: ±16 dB VPF (Variable Pre-shape Filter): center frequency 380 Hz (cut) VLE (Vintage Loudspeaker Emulator): frequency range 250 Hz - 20 kHz (cut) OUTPUT - AMP OUTPUT POWER: 500W RMS su 4 ohms / 300W RMS su 8 ohms LINE OUT: balanced XLR, max. voltage 10 Vpp EFFECT SEND: unbalanced, max. voltage 20 Vpp (pre-EQ) TUNER OUT: unbalanced, max. voltage 25 Vpp SPEAKER OUT: speakon + 1/4" SPEAKER - WOOFER/MID: 1 x 15" TWEETER: piezo - VEDI DESCRIZIONE SOTTOSTANTE BASS REFLEX: rear IMPEDANCE: 8 ohms SPEAKER POWER HANDLING: 400W RMS (AES Standard) CROSSOVER FREQUENCY: 3.5 kHz SENSITIVITY: 100 dB SPL COMBO - WEIGHT: 18.5 Kg HEIGHT: 46.4 cm WIDTH: 46.4 cm DEPTH: 48 cm

Vendo kit stereo formato da amplificatore SU-Z35 più sintonizzatore ST-Z200 perfettamente funzionanti e con le seguenti caratteristiche: Ampli: Power output: 30 watts per channel into 8Ω (stereo) Frequency response: 10Hz to 80kHz Total harmonic distortion: 0.03% Damping factor: 40 Input sensitivity: 2.5mV (MM), 150mV (line) Signal to noise ratio: 72dB (MM), 97dB (line) Channel separation: 50dB (line) Output: 150mV (line) Speaker load impedance: 4Ω to 16Ω Dimensions: 430 x 86 x 240mm Weight: 4.6kg Finish: silver Sinto: Type: Mono/Stereo Tuner Tuning Bands: FM, MW, LW Tuning Scale: Digital FM Tuning Range: 88 to 108 MHz MW Tuning Range: 525 to 1605 kHz LW Tuning Range: 145 to 350 kHz Sensitivity: 0.95uV (FM), 20uV (MW), 50uV (LW) Signal to Noise Ratio: 65dB (FM) Distortion: 0.3% (FM) Selectivity: 65dB (FM), 27dB (MW), 35dB (LW) Frequency response: 20Hz to 15kHz (FM) Output: 300mV Dimensions: 430 x 53 x 242mm Weight: 2.4kg Finish: silver Prezzo kit 50 euro Disponibile a qualsiasi prova e spedizione

Vendo casse B&W DM550 come nuove, per inutilizzo. Sotto trovate le principali caratteristiche. Viste le dimensioni ed il peso scambio a mano su Torino. Frequency Range: 56 Hz to 30 kHz (-6 dB points) Bass Loading: Second-order closed box alignment Frequency Response: 75 Hz – 20 kHz, ±2,5 dB on reference axis Dispersion: 20 Hz to 15 kHz Vertical: ±2 dB over 10° arc Horizontal: ±2 dB over 40° arc Sensitivity: 87 dB (2,83 V/ 1 m) Distortion (For 90 dB at 1 m) Second Harmonic: Less than 3% at 20 Hz to 200 Hz Less than 1% at 200 Hz to 20 kHz Third Harmonic: Less than 2% at 20 Hz to 200 Hz Less than 1% at 200 Hz to 20 kHz Impedance: Nominal 8 Ω (not faling below 4 Ω) Crossover: third-order acoustic response low-pass and high-pass Drive Units: 1 x 26mm high-frequency with aluminium dome, One 26mm coil on aluminium former, wound with polymide resin and heat cured 1 x 160mm bass/midrange with composite short fibre, 26mm coil on high temperature former, wound with polymide resin and heat cured Power Handling: Suitable for amplifiers with 10 W to 75 W output Dimensions (H x W x D): 352 x 204 x 243 mm (13-7/8" x 8" x 9-1/2") Weight: 5,5 kg (12 lbs)

Vendo coppia db technologies 715dx con cover originali come nuove. L'OPERA 715DX risulti essere la scelta ideale per applicazioni che richiedono un forte impatto sonoro anche sulle basse frequenze, senza quindi la necessità di aggiungere ulteriori subwoofer. Equipaggiato dal nuovo amplificatore Digipro G2 da 700 W, un nuovo DSP ed un woofer da 15” questo diffusore non teme rivali nella sua categoria. Grazie alla grande efficienza nelle frequenze basse è particolarmente indicato per DJ e musica live in genere anche se può essere utilizzato anche come monitor da palco. Dati tecnici Speaker Type2-Way Active Speaker Dati acustici Frequency Response [-10dB]48 - 20.000 Hz Frequency Response [+/- 3dB]58 - 19.000 Hz Max SPL129 dB HF1 " Type HFCompression driver Directivity80/65 x 60 ° HornAsymmetrical CD Horn LF15 " Amplificatore Amp Technologydigipro®G2 Amp ClassClass D Power PRG700 Watt Processore ControllerDSP 24bit/48kHz System PresetsFlat, Processed Limiterv Meccanica BoxPolyporpylen PP Angles UpMonitor use 43 ° Width432 mm (17.28 in) Height655 mm (26.2 in) Depth353 mm (14.12 in) Peso15,4 kg (33.07 lbs) Contattatemi solo se realmente interessati. Stiamo parlando di materiale professionale. Tags: rcf, proel, db technologies, energy, ld, yamaha, pioneer, shure, sennheiser, akg, quiklok.

Akiyama mx-1 usb professional dj mixer. come nuovo, usato solo una volta. vendo per mancato interesse nell'utilizzo. compreso di scatola originale e manuale. 90 euro + spese postali- 2 stereo channels (2 phono and 2 lines). mic channel (jack connector). 2 usb ports master output (1xrca) treble and bass tone control each channel with -12db cut. cue monitoring (headphones) with level control. master level. detachable crossfader. black colour. input level line: -14db/47k ohm +/- 3db phono: -50db/47k ohm +/- 3db mic: -54db/6k ohm +/- 3db output level master (rca): 0db/47k ohm +/-3db phones (load=32 ohm): -3db/33k ohm +/-3db max. output level (load =47k, thd=5%) master (rca): more than 18db (8v) phones (load=32 ohm): more than 5db (1.8v) channel balance: within 3db frequency response line: 20-20 khz +/- 3db phono: 20-20 khz +2, -3db (riia) mic: 20-20 khz +2, -3db output noise line: less than -75db phono: less than -65db mic: less than -55db distortion master output (load=47k ohm): less than 0.2% phones output(load=32ohm): less than 0.3% crosstalk more than 50db at 1khz between l and r channels equalizer low: +9/-26db +2/-3db a 100hz hi: +9/-26db +2/-3db a 10hz mic equalizer low: +10/-10db +2/-3db a 100hz hi: +10/-10db +2/-3db a 10hz usb section playback (eq flat, fader y master max) output: 0db (1v) +/-2db (-20dbfs, 1khz, gain max) thd+n: less than 0.02% (0dbfs, 1khz; w/ 20khz lpf, gain at 50%) frequency response: 20-20khz +/-2db (gain at 50%) s/n ratio: more than 89db (w/20khz lpf, a-weighed, gain a 50%) channel separation: more than 70db a 1khz (0dbfs, w/20khz lpf, a-weighted, gain at venter) recording and playback (line 1khz, -14dbv input, gain max) output: 4dbv (1.57v) +/-2db tdh+n: less than 0.05% general power consumption: ac9v (220v) dimensions: 228(w)x87(h)x265(d) mm weight: 2.8 kg includes 1 main unit (mx-1usb) 1 instruction manual 1 ac adaptor

Vendo deck piastra a cassette a nastro AIWA AD-370 perfettamente funzionante ha tasti servoassistiti dolby B-C e HX PRO regolazione manuale del bias la parte superiore ha ancora la pellicola in plastica da togliere Description The AD-F370 is a superb 2-head deck with the accent on easy operation and great music fidelity. A host of advanced features make the AD-F370 a remarkable sound value. Operation is easy thanks to the feather touch logic IC controls, which also enable Cue and Review operations for the speedy location by sound of desired musical passages. Dolby HX professional is incorporated for improved high frequency response regardless of tape type, while Dolby B and C noise reduction are also included to reduce tape hiss. Superb sound linearity is assured by the amorphous head, while the C,H and U versions feature Aiwa's super hard DX head for a corresponding level of performance. Specifications Type: 2-head, single compact cassette deck Track System: 4-track, 2-channel stereo Tape Speed: 4.8 cm/s Heads: 1 x record/playback, 1 x erase Motor: DC servo Tape Type: type I, CrO2, Metal Noise Reduction: B, C, HX Pro Frequency Response: 20Hz to 18kHz (Metal tape) Signal to Noise Ratio: 78dB (dolby C) Wow and Flutter: 0.065% Input: 50mV (line) Output: 0.35V (line) Dimensions: 430 x 127.5 x 233.4mm Weight: 3.3kg Year: 1989

The Yamaha AX Series 15" bass reflex subwoofer, complements the AX10, AX12, and AX15. Features include robust carpet covering, metal grilles and handles, pole mount socket. Frequency response covers the low bass range from 50Hz up to 200Hz, with 1000W peak power handling to move lots of air, enough to get your trouser legs flapping in the breeze. Caratteristiche Bass reflex enclosure. 15" speaker. 35mm pole mount socket. Frequency Response 50Hz-200Hz. Power Handling: 250W Noise, 500W Program, 1000W Maximum. 8 ohm nominal impedance. 97dB SPL 1W 1 meter. Input Connectors: 2 1/4" phone jack, 2 Neutrik Speakon NL4MP. Dimensions (W x H x D): 485 x 618 x 505. Weight: 26.5kg. Made in USA

Marchio: Definitive Audio Categoria: Sistemi a Colonna e Line Array Passive wide band column Speakers: 12 x 2,75’’ wide band Line Array Output power: 200 WRMS Frequency response: 200 Hz – 20 kHz SPL: 120 dB Impedance: 8 ohms Cabinet: aluminium Grid: 1 mm steel Cover included Dimensions: 1040 x 240 x 220 mm Weight: 7 kg Active vented subwoofer equipped with DSP Amplifier circuit: Class-D Speakers: 2 x 10’’ with 2.5’’ voice-coil 450Z RMS power: 500 W (Sub) + 250 W (Sat) Frequency response: 50 Hz – 200 Hz SPL: 121 dB Inputs: Combo (XLR / jack 6.35 mm) Outputs: balanced XLR, XLR link for VORTICE 210SA subwoofer and speakON for VORTICE columns Volume adjustment knob Sensitivity adjustment button: +4/-10 dBu DSP: 3 positions depending on the number of columns and boxes Compressor: excellent workmanship and operation Cabinet: high quality plywood Finishing: high resistance black paint Grid: 1.2 mm steel Power supply: 115 - 230 V∿ – 50/60 Hz switchable voltage indicator: LED Dimensions: 585 x 455 x 755 mm Weight: 23.5 kg

Power: 100 W RMS - 200 W max Frequency response: 180 Hz -20 KHz SPL max. (@1 m): 116 dB Nominal impedance: 4 ohms Speaker: 6 x 2.75" full-range Dispersion: 120° x 20° (HxV) Connector: integrated in base Dimensions: (80 x 80 x 830 mm) x2 Net weight: 2.45 kg + 1.20 kg = 3.65 kg Power: 150 W RMS - 300 W max Frequency response: 50 - 200 Hz SPL max. (@1m): 116 dB Nominal impedance: 4 ohms Boomer: 8 inches Dimensions: 340 x 430 x 400 mm Net weight: 12.6 kg Bass stage: 1 x 150 W RMS / 300 W max Class D / 4 Ohms Mid/high stage: 1 x 100 W RMS / 200 W max Class D / 4 Ohms