Level control on each channel

Vendo Mixer 8 canali BOSS BX8 8 linee in entrata, uscita stereo, slider master volume separati numerosi effetti con controllo d'intensità, ingresso jack per line CARATTERISTICHE: -Overload Indicators: This lighrs up when the input signal level of each channel is too high -Gain Knobs: The Gain Knobs of each channel adjusts the mout gain for mixing -Treble Knobs -Bass Knobs -Effect-Send Knobs: These knobs control the level of the signals to be sent to the Effect -Headphone Level Knob: -Level Meters: These indicate the level of the output signals. -Master Faders (L, R): These sliders control the overall volume of the mixed signals separately for left and right. -Pilot Lamp: When the mixer is turned on. this lamp lights up -Power Switch: -Output level Selector Switch: This switch selects output level ot the signal sent from the Output Jacks. At the "+4" position. the rated output level (the output level when the Level -Effect1 Return Knobs: This knob controls the Mixing level of the signal returned -Effect2 Return Knobs: -Send Jack: -Headphone Jack: -Input Jacks: -Effect 1 Send Jack: -Effect 2 Send Jack: -Effect 1 Return Jack: -Output Pin Jacks: -Output Jacks (L&R): Alimentatore su richiesta (venduto separatamente)

Column Power: 180W RMS - 360W max Nominal impedance: 6 Ohms Boomer: 6 x 3 inches Tweeter: 1 x 1 inch Dispersion: 120° x 30° (HxV) Connector: Insert in cabinet Dimensions: 103 x 750 x 100 mm x 2 Net weight: 3.7 kg Subwoofer Power: 250W RMS - 500W max Nominal impedance: 4 Ohms Boomer: 1 x 12 inches / 2,5" voice coil Dimensions: 389 x 626 x 666 mm Net weight: 28 kg Assembly Frequency response: 35 - 18,000Hz Max SPL. (@1m): 127 dB Amplification: Bass stage: 1 x 300W RMS / 1200W Dynamic Mid/high stage: 1 x 300W RMS / 1200W Dynamic Inputs CH1: 1 x XLR/line jack/mic combo CH2: 1 x XLR/Line Jack/Mic Combo CH3: 1 x Line Jack CH4/5: 1 x RCA L/R line + Bluetooth® input Outputs 1 Insert on top of the cabinet for the column 1 x XLR MIX OUT balanced for output to another system • DSP 24 bit (1 in 2 out) EQ / Presets / Low cut / Delay / Bluetooth® 5.0 TWS ROOM type reverb adjustable on channels 1 and 2 • Level: Level control on each channel + Master • Sub: Subwoofer level control Delivered with a cover for the subwoofer and a cover for the columns

Marchio: Audiophony Categoria: Mixer analogici 4 channel mixer, 2 microphones, 2 stereo, 1 aux and USB port 2 x microphone inputs via XLR plugs 2 x 6.35 mm jack balanced line input 2 x unbalanced stereo inputs on RCA and 3.5 mm jack 2-band equalizer on MIC/line and stereo channels Gain control for each channel AUX level setting on each channel Balanced MAIN output on 6.35 mm jack Unbalanced Record output via RCA plugs Balanced AUX output on 6.35 mm jack Monitoring output via 6.35 mm stereo jack 1 USB port for connecting a computer LED VU-meter for MAIN output

Marchio: Audiophony Categoria: Mixer analogici 6 channel mixer 4 microphones, 2 stereo, 1 aux and USB port. 4 microphone inputs via XLR plugs 4 Jack 6.35 balanced line input. 2 unbalanced stereo inputs on RCA and 3.5 jack 2-band equalizer on mic/line and stereo channels Gain control for each channel AUX level setting on each channel Balanced MAIN output on 6.35 Jack Unbalanced Record outputVia RCA plugs Balanced AUX output on 6.35 Jack Monitoring outputVia stereo Jack 6.35 1 USB port for connecting a computer LEDVu-meter for MAIN output

Satellite Power: 400 W RMS - 800 W max. Nominal impedance: 4 ohm Woofer: 3 x 8" neodymium Tweeter: 12 x 1" Dispersion: 100° x 70° (H x V) (-10 dB) Dimensions: 255 x 695 x 400 mm Net weight: 11.5 kg Subwoofer Power: 700 W RMS - 1400 W max. Nominal impedance: 4 ohm Woofer: 1 x 15" Dimensions: 483 x 725 x 585 mm Net weight: 36.5 kg Satellite + subwoofer Frequency response: 35 - 18,000 Hz SPL max. (@ 1 m): 128 dB Amplification Low stage: 1 x 700 W RMS / 1400 W max. at 4 ohm Mid/high stage: 1 x 400 W RMS / 800 W max at 4 ohm Level: level adjustment on each channel + master Sub: adjustment of the level of the box Inputs CH1: 1 x XLR Combo / line jack / MIC CH2: 1 x XLR / line jack / MIC Combo CH3: 1 x line jack CH4/5: 1 x RCA L/R line + Bluetooth input Input impedances MIC 1/2: balanced 40 kohm Line 1/2: symmetrical 10 kohm Line 3: symmetrical 20 kohm Line 4/5: asymmetrical 5 kohm Outputs 1 x insert on top of the satellite box 1 x XLR MIX OUT balanced for output to another system 2 x XLR LINE OUT symmetrical for repique CH1 and 2 DSP 24 bit (1 in 2 out) EQ / presets / low cut / delay / Bluetooth TWS

Marchio: Audiophony Categoria: Casse Attive con Mixer Integrato 2 channels XLR3-F/TRS combo Line/Mic input 1 Stereo RCA channel 1 1/8" AUX channel 1 Bluetooth connexion 2 UHF microphones Outputs: 1 TRS mix output Loudspeaker: 12" loudspeaker + 1.35" titanium driver, total impedance: 4Ω Power: 150 W RMS/DC 250 W RMS/AC Class D amplifier Response curve: 55 Hz- 20 kHz Sound pressure level: 118 dBSPL max UHF DiversityWith 16 frequencies Handheld cardioid-dynamic microphone Frequency range UHF 514 ~ 542 MHz - 10 mW Built-in USB key / SD card reader and Bluetooth receiver SuppliedWith an infrared remote control The player features a Bluetooth receiver TypeV2.0 AVRCP,With an excellent, close-to-digital audio transmission Independent level settings for each channel Low and treble equalizer from -12 dB to + 12dB Echo and Delay effects on the microphone channels Power and Limit Indicator Battery charge indicators Finish: Polypropylene housing, metal mesh grill. C36 mounting plate for speaker stands Dimensions (mm): 615 x 350 x 395 NetWeight (incl. batteries): 24.5 kg Batteries: 2x 18V / 7Ah Lead Acid Autonomy: 6 hours depending on theVolume Charging time: 8 hours to recharge the two 18V batteries LED display to indicate the charge level. Charge it and use it at the same time. Automatic shutdown if the battery level is too low.

Marchio: Audiophony Categoria: Finali di potenza Class-D amplifier Switched-mode power supply Mode selection: Stereo, Bridge or Parallel Independent limiter for each channel Extremely accurate and independent level settings for each channel LEDs indicators Convection cooled Balanced Jack TRS and XLR inputs Unbalanced RCA outputs Binding post-jacks or speakON outputs Short-circuit, over current and high temperature independent protections for each channel 2x19" rack mount spaces Stereo Max power: 4 Ω RMS stereo power (minimum): 2 x 150 W RMS; 8 Ω RMS stereo power: 2 x 80 W RMS Mono bridged Max power: 8 Ω bridged power (minimum): 1 x 300 W RMS Signal-to-noise ratio Less than 90 dB Input sensitivity: 4 dBu +/-2 dB Distortion: THD at 1 kHz 1/2 rated power Less than 0.1%; Slew rate: - 65 dB at 1 kHz; Frequency response (4 Ω/1 W): +0.5 dB; 20 Hz-20 kHz Input impedance: unbalanced 15 kΩ / Balance 30 kΩ Clip: 0 dBr Cooling: Convection cooled Input connectors: XLR3-F, Balanced 6.35 mm TRS-F jack + Unbalanced RCA Output connectors: Binding post-jacks + 4-pole speakON® Front control panel: AC power switch, Channel 1 and 2Volume Rear control panel: Mode selection button Indicators: Protect (red) / Clip (yellow) / Signal (green) Protections: Short-circuits, over current and high temperature protected Power supply: 100/230 V AC - 50/60 Hz Dimensions: 482 mm x 44 mm x 330 mm NetWeight: 4.3 kg

Marchio: Audiophony Categoria: Finali di Potenza Class-D amplifier Switched-mode power supply Mode selection: Stereo, Bridge or Parallel Independent limiter for each channel Extremely accurate and independent level settings for each channel LEDs indicators Convection cooled Balanced Jack TRS and XLR inputs Unbalanced RCA outputs Binding post-jacks or speakON outputs Short-circuit, over current and high temperature independent protections for each channel 2x19" rack mount spaces Stereo Max power: 4 Ω RMS stereo power (minimum): 2 x 150 W RMS; 8 Ω RMS stereo power: 2 x 80 W RMS Mono bridged Max power: 8 Ω bridged power (minimum): 1 x 300 W RMS Signal-to-noise ratio Less than 90 dB Input sensitivity: 4 dBu +/-2 dB Distortion: THD at 1 kHz 1/2 rated power Less than 0.1%; Slew rate: - 65 dB at 1 kHz; Frequency response (4 Ω/1 W): +0.5 dB; 20 Hz-20 kHz Input impedance: unbalanced 15 kΩ / Balance 30 kΩ Clip: 0 dBr Cooling: Convection cooled Input connectors: XLR3-F, Balanced 6.35 mm TRS-F jack + Unbalanced RCA Output connectors: Binding post-jacks + 4-pole speakON® Front control panel: AC power switch, Channel 1 and 2Volume Rear control panel: Mode selection button Indicators: Protect (red) / Clip (yellow) / Signal (green) Protections: Short-circuits, over current and high temperature protected Power supply: 100/230 V AC - 50/60 Hz Dimensions: 482 mm x 44 mm x 330 mm NetWeight: 4.3 kg

Akiyama mx-1 usb professional dj mixer. come nuovo, usato solo una volta. vendo per mancato interesse nell'utilizzo. compreso di scatola originale e manuale. 90 euro + spese postali- 2 stereo channels (2 phono and 2 lines). mic channel (jack connector). 2 usb ports master output (1xrca) treble and bass tone control each channel with -12db cut. cue monitoring (headphones) with level control. master level. detachable crossfader. black colour. input level line: -14db/47k ohm +/- 3db phono: -50db/47k ohm +/- 3db mic: -54db/6k ohm +/- 3db output level master (rca): 0db/47k ohm +/-3db phones (load=32 ohm): -3db/33k ohm +/-3db max. output level (load =47k, thd=5%) master (rca): more than 18db (8v) phones (load=32 ohm): more than 5db (1.8v) channel balance: within 3db frequency response line: 20-20 khz +/- 3db phono: 20-20 khz +2, -3db (riia) mic: 20-20 khz +2, -3db output noise line: less than -75db phono: less than -65db mic: less than -55db distortion master output (load=47k ohm): less than 0.2% phones output(load=32ohm): less than 0.3% crosstalk more than 50db at 1khz between l and r channels equalizer low: +9/-26db +2/-3db a 100hz hi: +9/-26db +2/-3db a 10hz mic equalizer low: +10/-10db +2/-3db a 100hz hi: +10/-10db +2/-3db a 10hz usb section playback (eq flat, fader y master max) output: 0db (1v) +/-2db (-20dbfs, 1khz, gain max) thd+n: less than 0.02% (0dbfs, 1khz; w/ 20khz lpf, gain at 50%) frequency response: 20-20khz +/-2db (gain at 50%) s/n ratio: more than 89db (w/20khz lpf, a-weighed, gain a 50%) channel separation: more than 70db a 1khz (0dbfs, w/20khz lpf, a-weighted, gain at venter) recording and playback (line 1khz, -14dbv input, gain max) output: 4dbv (1.57v) +/-2db tdh+n: less than 0.05% general power consumption: ac9v (220v) dimensions: 228(w)x87(h)x265(d) mm weight: 2.8 kg includes 1 main unit (mx-1usb) 1 instruction manual 1 ac adaptor

UHF410-Base F5 receiver True Diversity Receiver Frequency range: UHF 514~564 MHz Frequencies: 997 programmed,With Auto-scan function Channel presets: 8 groups, 16 compatible channels in each group Channel Selection Mode: Manual, Tact Switch, Auto-Scan, SYNC LCD display: frequency, group, channel, RF b'&' AF Audio outputs: XLR3-M balanced and 6.35 TS-F jack Output levels: line or micro Oscillator: PLL SyntheDimensionsr Frequency stability: ± 0.005%. Modulation mode: FM H.H.T.: b' Audio Frequency Response: 80 Hz to 18 kHz Volume control by rotary switch on the front panel Squelch adjustment by rotary selector at the rear Detachable BNC antennas, many accessories available Power supply: 12 V DC (adapter supplied) Current consumption: 260mA ± 10mA Dimensions: 200 x 42 x 183 mm (½U 19", rackable in pair) BODYPACK TRANSMITTER True Diversity transmitter Frequency ranges: UHF 514~564 MHz Max power: 35 m W (max.) Frequencies: 997,With Auto-scan function LCD display: channel, battery level Mic input: mini XLR3-F Gain level: -20/-10/0dB Power supply: 2 x LR6/AA type 1,5V batteries (not supplied) Lavalier microphone Sensitivity: -67 ±3dB Directivity: Omnidirectional Frequency response: 50 Hz à 10 kHz Max current: 10V Standard current: 1.5V Power consumption: 0.5 mA max. S/N ratio: More than 58dB Supplied accessory:Windshield and clip Connector: mini-XLR3-M

Equalizzatore originale americano, 110 volt Frequency Response: 20Hz to 20,000Hz +/- 0.5dB Hum and Noise: 90dB (79uV) below 2.5V flat response. 85dB (140uV) below 2.5V worst case. Harmonic and Intermodulation Distortion: less than 0.02% at 2.5V output 20Hz to 20,000Hz Low frequency Compensation: Variable from 0 to +17dB at 20Hz Input Sensitivity: 2.5V into 27k ohms for rated output with controls set for flat response High Frequency Compensation: Variable +/-10dB at 20,000Hz Output Level and Impedance: 2.5V into 10k ohms or more with the output level at zero and all other controls set for flat response. Programmable Filters: 14 sections (7 per channel) each of which can be programmed for standard 1/3 octave center frequencies from 20Hz to 1000Hz. Filter bandwidth is programmable for narrow (approx. 1/3 octave) or wide (approx. 1 octave). Amplitude is continuously adjustable +/- 12dB for narrow and +/-15 dB for wide. A detented control is used to position for flat response. Programming is achieved by means of plug-in capacitors provided with the MQ107. Size: 3-1/2" high, 5-3/4" wide and 14" long Finish: Chrome and black Weight 7 lbs. 9 oz.

Marchio: Marani Pro Audio Categoria: Finali di Potenza Power output: 8 x 250 W @ 4Oohm 4 x 500W @ 8ohm (modalità bridge)- 2 Switched-Mode con PFC attivo e auto voltage sensing - Classe D, modulatore full PWM larghezza di banda con distorsione ultra bassa- Circuiti di protezione completa con Over-Current, Over / Under-Voltage, uscita DC e sovra-temperatura - 8 ingressi Mic/Line, 8 uscite con mixaggio DSP Engine: 3 bande di equalizzazione parametrica per ogni canale di ingresso - 5 bande di equalizzazione parametrica per ogni canale di uscita - Gain Control, Noise Gate, Feedback Eliminator (Mic input only) per canale input - Tempo di ritardo regolabile fino a 850 ms per ogni canale di ingresso e di uscita Direct PC/Network Connection: Connettore USB sul pannello frontale per le connessioni dirette al PC - Interfaccia Ethernet RS485 per la configurazione del sistema, monitoraggio e controllo remoto Controlli: Pannello di controllo Display LCD interattivo anteriore per l'accesso e la configurazione locale - 4 ingressi digitali per ulteriori 4 selezioni predefinite con configurazione priorità - 4 porte di uscita digitali per l'attivazione di dispositivi esterni- Software per dispositivo Apple iPad che consente il controllo simultaneo fino a 32 unità, l'impostazione di tutti i parametri, mostrando i livelli in tempo reale - Telecomando opzionale Marani CP4 Wall Panel Numero di canali: 8 Max Output Power @8ohm: 8 x 125W 4 x 250W (Bridge) Max Output Power @4ohm: 8 x 250W; 4 x 500W (4? BTL Mode selected) Circuito di uscita: Classe D Output Voltage: 70 Vp / 140 Vpp (unloaded) / Bridged 140 Vp / 280 Vpp (unloaded) THD @ Rated power 4ohm (1kHz): b' Rapporto segnale rumore:b'>' 120 dB (A ponderato, 20 Hz - 20 kHz, carico di 8ohm) Risposta in Frequenza: 20 Hz - 20 kHz ± 0,15 dB (8ohm di carico, 1 dB potenza nominale di seguito) Fattore di smorzamento: b'>'1000 (8ohm di carico, 1kHz e sotto) Alimentazione: Due alimentatori switching indipendenti con PFC (Power Factor Correction) Raggio di azione: Universale di rete, 85-265V Consumo / assorbimento di corrente e la dissipazione termica 230V: - 22.4W / -A / 76.6 BTU/h (Idle)- 346W / -A / 286.8 BTU/h (I/8 max. power@4ohm) Protezioni: Over-Current, Over/Under Voltage, Output DC and Over-Temperature Analog Input: 8 elettronicamente bilanciati; Max Input Level: Line +18dBu; Mic -18dBu Analog Output: 8 electronically balanced; Max Output Level: +18dBu /AD b'&' DA Converters: 1x AK5385B 24bit, 2x AK4358 24bit DSP Engine: Dream SAM3716, 24bit (data) x 6 bit (coeff.) Risoluzione DSP: 24 × 32 bit per il processo di filtraggio; Risoluzione 6 bit sui risultati di calcolo intermedi Equalizzazione input: parametrico a 3 bande selezionato come Peaking o Low/High Shelving con Q variabile per ogni canale di ingresso Equalizzazione Output: parametrico a 5 bande selezionato come Peaking o Low/High Shelving con Q variabile per ogni canale di uscita Filter Gain: da -12dBu fino a +12dBu by 0.5dBu per punti di risoluzione Centro di Frequenza: Selezionabile con un 1/24 di risoluzione ottava step da 20Hz fino a 20kHz Filtro Q/BW: da 0,4 fino a 10 da 0,1 punti di risoluzione Crossover Section HPF/LPF: - Butterworth 6/12/18/24/48dB per ottava- Bessel, Linkwitz-Riley personalizxabili 12/18/24/48dB per ottava - Filter resolution 1/24th di ottava RMS Compressor e Peak Limiter:- Soglia da 18dBu fino a -30dBu - Tempo di attacco da 5ms a 200ms (risoluzione di 1ms a 20ms, 10ms risoluzione fino a 100 ms e risoluzione di 20 ms fino a 200 ms)- Tempo di rilascio da 0,1 sec a 3 sec (risoluzione 0,1 sec)- Rapporto da 1: 1 a 32: 1 (Compressore solo) Risposte Eliminator: Pitch Shifting algoritmo solo per i canali di ingresso Mic Pannello Frontale: Display LCD 2×24 con retroilluminazione LED verdeMeter - 6-LED status indicators per channel (Line, Mic, FBK, Signal, Clip, Limiter)- 1-LED indicator Phantom Power- 6 x preset selection push button switch- Connettore USB di tipo B Pannello posteriore: 2 x 12 pin Phoenix connector (Mic/Line Input)- 2 x 12 pin Phoenix connector (Line Output)- 2 x 8 pin Phoenix connector (Speaker Outputs)- 2 x 4 pin Phoenix connector (S1-S4 digital input ports - TTL level 0-5V)- 2 x 4 pin Phoenix connector (S1-S4 digital output ports - TTL level 0-5V)- 2 x RJ45 per RS485 In/Out - 1 x RJ45 con activity LEDs (10/100 TCP-IP) - IEC C13 16A connector; Power on /off switch Dimensioni: 483x89x515 mm 2RU Peso: 12 Kg

La confezione scatola contiene: N- 1 Trasmettitore SIEM-2T con alimentatore N. 1 Ricevitore SIEM-2R N. 1 Auricolari ear monitor IE-1 Prezzo al nuovo: €280 Trasmettitore SIEM-2T 16 canali a disposizione,due ingressi mic/line miscelabili, la portata di 60 metri. Gamma di frequenza 502 ~ 960 MHz Potenza di uscita RF 10 mW Deviazione di frequenza nominale (modulazione) ± 40KHz Audio Impedenza di ingresso 20kO Livello ingresso nominale -20 dBV Massimo Livello di ingresso 0 dBV Display LED AF Level, Channel Connettore di ingresso audio 2 x XLR bilanciato Loop Out Connector 2 x Ø6.3mm Balanced Loop Out Socket Tensione di funzionamento 12-18 VDC, 600 mA Ricevitore SIEM-2R Frequency Preparation PLL Synthesized Control Gamma di frequenza 502 ~ 960 MHz LED Display Channel Controls Power On / Off, Selezione del canale, Controllo del volume Audio Risposta in frequenza 40 ~ 18.000 Hz Connettore di uscita 1/8 Jack stereo Durata della batteria 14 ore circa Batteria: 2 batterie AA Auricolari IE-1 Risposta in frequenza 20 ~ 20.000 Hz Tipo di trasduttore dinamico Impedenza 16 Ohm Sensibilità (a 1000Hz) 114 dB / mW Distorsione meno dello 0,3 Lunghezza del cavo 148 cm con connettore stereo ø3.5 Peso: 6 gr