Low high frequency boosts

Vendo amplificatore per basso Mark Bass Mini CMD 151P "Custom" Dettagli tecnici sul sito Mark Bass - CUSTOMIZZAZIONE - L'amplificatore e' stato customizzato con queste modifiche: - Tweeter originale (piezo) sostituito con tweeter a ferrofluido Monacor HT-30 - Amplificatori operazionali del preampli (originali: TL072, 0.32 EUR/chip) sostituiti con OPA1642 (SoundPlus Series, 1.91 EUR/chip) - Condensatori elettrolitici del preampli (segnale e alimentazione) sostituiti con componenti a basso ESR / 105 gradi - Jack input, send e return, uscita cassa sostituiti con jack professionali Neutrik - Ventolina raffreddamento sostituita con una a bassa rumorosita' Rispetto all'ampli non customizzato, il suono e' molto piu' definito e dinamico e non presenta piu' quegli alti taglienti enfatizzati dal tweeter piezo originale. Il rumore di fondo (hiss) e' diventato praticamente inesistente. - CONDIZIONI - L'amplificatore e' stato COMPLETAMENTE REVISIONATO (spolverato, pulito, disossidato e testato) a gennaio 2020 Woofer in condizioni perfette (vedi foto) L'unico difetto e' la moquette originale che si e' parzialmente staccata su un lato (vedi foto), dovuta alle centinaia di concerti che ha fatto (visto che suona bene!) Qualsiasi prova a casa mia, se volete portatevi il vostro basso per provarlo per bene Fornisco insieme all'ampli il manuale, il cavo corrente e il tweeter piezo + resistenza originali Non faccio spedizione visto l'ingombro / peso, solo ritiro a mano "visto e piaciuto" INPUTS - INPUT: impedance 500 kOhm, max. voltage 15 Vpp BALANCED INPUT (XLR): impedance 22 kOhm, max. voltage 25 Vpp EFFECT RETURN: impedance 22 kOhm, max. voltage 25 Vpp FREQUENCY RESPONSE: 40 Hz to 18 kHz CONTROLS - GAIN: -80 dB to +23 dB range MASTER VOLUME GROUND LIFT (switch on rear panel) EQUALIZATION - LOW: center frequency: 40 Hz; level: ±16 dB LOW MID: center frequency: 360 Hz, level: ±16 dB HIGH MID: center frequency: 800 Hz, level: ±16 dB HIGH: center frequency: 10 kHz, level: ±16 dB VPF (Variable Pre-shape Filter): center frequency 380 Hz (cut) VLE (Vintage Loudspeaker Emulator): frequency range 250 Hz - 20 kHz (cut) OUTPUT - AMP OUTPUT POWER: 500W RMS su 4 ohms / 300W RMS su 8 ohms LINE OUT: balanced XLR, max. voltage 10 Vpp EFFECT SEND: unbalanced, max. voltage 20 Vpp (pre-EQ) TUNER OUT: unbalanced, max. voltage 25 Vpp SPEAKER OUT: speakon + 1/4" SPEAKER - WOOFER/MID: 1 x 15" TWEETER: piezo - VEDI DESCRIZIONE SOTTOSTANTE BASS REFLEX: rear IMPEDANCE: 8 ohms SPEAKER POWER HANDLING: 400W RMS (AES Standard) CROSSOVER FREQUENCY: 3.5 kHz SENSITIVITY: 100 dB SPL COMBO - WEIGHT: 18.5 Kg HEIGHT: 46.4 cm WIDTH: 46.4 cm DEPTH: 48 cm

Martin Logan Montage Diffusori da pavimento compatti in finitura come da immagine. • Garanzia 3 mesi sul perfetto funzionamento • non disponibile imballo originale • Permuta valutabile fino a concorrenza del 30% del prezzo netto di cessione • Prezzo scontabile per chiusura trattativa rapida, senza permuta Prezzo di listino la coppia: 1900 euro PROPOSTI AD UN PREZZO INCREDIBILE! -> Da ritirare presso lo showroom di Brescia Condizioni estetiche (8,5/10) e condizioni funzionali perfette (10/10). Contatta Consound per verificare la disponibilità. Specifiche tecniche Frequency Response: 47–20,000 Hz ±3dB Recommended Amplifier Power: 20‒300 watts per channel Sensitivity: 90 dB/2.83 volts/meter Impedance: 5 Ohms. Compatible with 4, 6, or 8 Ohm rated amplifiers. Crossover Frequency: 2500 Hz High Frequency Transducer: 3.8 × 5.7 cm ATFâ„¢ Transducer Low Frequency Transducer: 2 × 16.5cm high rigidity aluminum cone with extended throw drive assembly, non-resonance asymmetrical chamber format; bass reflex Components: Air core coils, metal film and low dissipation electrolytic capacitors Inputs: Custom 5-way binding posts Weight: 13.6 kg Dimensions: 96.5cm × 24cm × 29.7cm

Causa inutilizzo vendo impianto audio professionale cosi composto: 2 casse passive Toa/Onkyo mod. 380 SE - 3 vie - woofer da 15'' + tromba medi + tweeter (vedi caratteristiche sotto allegate) perfette - originali - mai riparate - 380 watt rms - mede in Canada (USA) + finale di potenza Toa/ Onkyo P 150 D - 180 + 180 watt su 8 ohm - perfetto ed originale - una macchina superaffidabile - Se devi fare un impianto fisso in una sala da ballo media - o un impianto di ottima qualita audio fa un grande affare. L'impianto NON è vendibile separatamente - ed è perfettamente funzionante ed originale- Fatto controllare da laboratorio specializzato a Torino Dato il peso degli oggetti NON è possibile la spedizione - Le foto sono reali degli oggetti in vendita - NO perditempo - NON trattabile - NO scambi merce - no cercatori di foto - se sei realmente interessato contattami al cellulare 347 0083722 Annuncio visibil = merce disponibile Caratteristiche tecniche delle casse Enclosure: Vented (bass reflex) type Speakers: Low Frequency, 15" woofer Mid Frequency, CD Horn plus compression driver High Frequency, Horn tweeter Power Handling Capacity Continuous Pink Noise: 120 watts RMS of band-limited pink noise (50 Hz~20 kHz) Continuous Program: 360 watts Impedance: 8 ohms Sensitivity: 102 dB (1W/1m) Input Panel Frequency Response: 50 Hz~20 kHz Crossover Frequencies: 800 Hz, 8 kHz High and Mid Frequencies Level Controls: 0~ –10 dB (with an "OFF" position) Input Terminals: ¼" Phone jacks for a full-range, biamp, triamp and chaining Finish (Enclosure): Polyester in grey color Dimensions: 758(H)X498(W)X410(D)-mm 29.8(H)X19.6(W)X16.1(D) inches Weight: 36 kg (79.2 Ibs)

1400W + 700W – 137DB SPL ACTIVE PRECISION COVERAGE VERTICAL ARRAY 2-way powered bi-amplified true line array, bass reflex design, internal Digital Signal Processor 1400Wrms LF and 700Wrms HF Class D (PWM) high efficiency integrated amplifier 8 woofer custom al neodimio da 200mm (8’’)50 mm voice coil (2”) 8 x 25 mm (1”) custom neodymium compression drivers and 44 mm voice coil (1.7”) 8 polypropylene waveguide horns with 90° horizontal dispersion 15° vertical dispersion On-board presets allow different equalization configurations, gain and digital delay through the rear control panel Specifications Configuration way: 2 Built-in amplifiers LF/HF (Wrms): 1400/700 Frequency response (-6dB): 58Hz – 18kHz Low frequency woofer (inch): 8 x 8 – 2 coil – neodymium High frequency driver (inch): 8 x 1 – 1,7 coil – neodymium Sensitivity (1W/1m): 105 dB Maximum SPL: 137 dB Dispersion (H x V): 90° x 15° Input impedance (kohm): 22 Crossover frequency (kHz): 1,2 AC Power requirements (VA): 1400 Input connectors: XLR with loop Power cord: 5 / 16,4” (m/ft) Net dimensions (WxHxD – single unit): 713x980x460 / 28,1×38,6×19,3 (mm / inch) Net weight (kg/Lb): 93 / 205,02 Transport dimensions (WxHxD – 2 units on pallet): 750x1400x1100 / 29,5×55,1×43,3 (mm / inch) Transport weight (2 units on pallet): 210 / 462,97 (kg/Lb) PRODOTTO USATO: CONDIZIONI OTTIME

Le trombe vengono fornite con membrane originali beyma nuove 3206382238 disponibili driver e trombe rcf b e C 18 sound, beyma, faital. fatene richiesta. disponibili beyma cp550 THE BEYMA CP350/TI 1" HIGH FREQUENCY COMPRESSION DRIVER FEATURES A PURE TITANIUM DOME & SUSPENSION INCREDIBLE CLARITY & DEFINITION WITH A SMOOTH RESPONSE W/ VERY LOW DISTORTION EVEN AT HIGH VOLUMES HORN INSTRUMENTS, VOCALS AND DRUM SOUNDS ARE PRECISE, CLEAN AND STRONG SOUNDING THE SOUND FROM THIS DRIVER JUMPS OUT AT YOU MAKING YOU FEEL THE INSTRUMENTS & VOCALS ARE RIGHT IN FRONT OF YOU FOR ALL HIGH POWER PRO HIGH FREQUENCY APPLICATIONS INCLUDING P.A. SYSTEMS, SOUND REINFORCEMENT, ETC.

Equalizzatore originale americano, 110 volt Frequency Response: 20Hz to 20,000Hz +/- 0.5dB Hum and Noise: 90dB (79uV) below 2.5V flat response. 85dB (140uV) below 2.5V worst case. Harmonic and Intermodulation Distortion: less than 0.02% at 2.5V output 20Hz to 20,000Hz Low frequency Compensation: Variable from 0 to +17dB at 20Hz Input Sensitivity: 2.5V into 27k ohms for rated output with controls set for flat response High Frequency Compensation: Variable +/-10dB at 20,000Hz Output Level and Impedance: 2.5V into 10k ohms or more with the output level at zero and all other controls set for flat response. Programmable Filters: 14 sections (7 per channel) each of which can be programmed for standard 1/3 octave center frequencies from 20Hz to 1000Hz. Filter bandwidth is programmable for narrow (approx. 1/3 octave) or wide (approx. 1 octave). Amplitude is continuously adjustable +/- 12dB for narrow and +/-15 dB for wide. A detented control is used to position for flat response. Programming is achieved by means of plug-in capacitors provided with the MQ107. Size: 3-1/2" high, 5-3/4" wide and 14" long Finish: Chrome and black Weight 7 lbs. 9 oz.

Prodipe Natural 6 b'/xc3/xa8' un amplificatore per chitarra acustica da 140 watt dotato di 2 ingressi microfonici con guadagno, EQ a 3 bande, riverbero, volume con l'opzione di alimentazione phantom, 1 ingresso single-ended con guadagno, EQ a 3 bande, riverbero, volume, 1 canale stereo con EQ a 2 bande e volume (stereo RCA), uscita stereo (RCA stereo), uscita mono bilanciata (XLR). Frequency range: 50Hz -20KHz Tweeter: 1b'"' (25mm) - Neodymium Dome Woofer: 6b'/xc2/xbd'b'"' (165mm) - Fibreglass membrane Amplification: HF Power RMS (peak): 40W (60W) LF Power RMS (peak): 100W (180W) Signal to Noise ratio: 92dB SPL level (max): 114dB Input/output impedance: Balanced XLR: 1.5MΩ Unbalanced Jack: 1MΩ RCA: 22Ω EQ boost/cut range: +/- 15dB High frequency: 12KHz Mid frequency: 2.5KHz Low frequency: 80Hz Electronic filtering: Cut-off Frequency: 2.6KHz Subsonic Filter: 45Hz Fuse rating: 100V - 120V: 3.15A 220V - 240V: 1A Audio inputs: 2 XLR/Jack 1 Jack 1 stereo RCA Audio outputs: 1XLR 1 Jack 1 stereo headphone set Dimensioni (H x L x P) en mm: 390 x 320 x 285 Peso: 13kg

Marchio: FBT Categoria: Casse Attive Cabinet in polipropilene con stampaggio ad iniezione di gas progettato per eliminare risonanze indesiderate. Altoparlanti custom FBT ad alta efficienza e con elevata capacità di escursione lineare. Drivers a compressione con apertura da 25mm e bobina da 35mm. Amplificatore in Classe D da 1200W LF e 300W HF ad alta dinamica. Woofer custom da 320mm con bobina da 64mm Tromba 90°H x 60°V Alimentatore universale switching 100-240Vac. Bluetooth 5.0 Processore DSP con 4 presets di equalizzazione. Algoritmi avanzati di filtraggio, equalizzazione dinamica delle basse frequenze, energy control che cambiano in funzione del preset scelto. Mixer a 3 canali: un canale dedicato BLUETOOTH 5.0, due canali micro/ linea indipendenti con volume separato e uno dotato di ingresso jack stereo Uscita XLR bilanciata MIX o CH1 LINK. Maniglie integrate, punti di ancoraggio M10 per installazione sospesa, supporto per stativo, profilo monitor del diffusore a 30° e 45°. CONFIGURATION: 2 way BUILT-IN AMPLIFIER LF/HF: 1200/300 FREQUENCY RESPONSE: 50Hz - 20kHz LOW FREQUENCY WOOFER: 12 - 2.5 coil HIGH FREQUENCY DRIVER: 1 - 1.4 coil MAXIMUM SPL CONT/PEAK: 124/129 DISPERSION: 90°x60° INPUT IMPEDANCE: 22 INPUT CONNECTOR: XLR IN/OUT, Jack ST POWER CORD: 9.8ft / 3mt NET DIMENSION (WXHXD): 14.01x24.37x14.05 / 356x619x357 NET WEIGHT: 35.93/16.3 TRANSPORT DIMENSION (WXHXD): 17.32x27.55x17.51 / 440x700x445 TRANSPORT WEIGHT: 41.66/18.9

Vendo per inutilizzo Subwoofer JBL Attivo come nuovo,qualsiasi prova. Le specifiche: Active Subwoofer Section Low Frequency Cut-off: 35Hz High Frequency Cut-off: 40Hz - 160Hz Variable Built-In Amplifier Power: 100 Watts RMS Drive Units: 200mm Paper Cone Long Throw Driver Bass Reflex Enclosure Dimensions (H x W x D): 450mm x 250mm x 360 mm Weight: 13.6kg

AMPLIFICATORE INTEGRATO NIKKO TRM-230 STEREO AMPLIFIER Frontale in alluminio Scocca in Legno Potenza 2 x 32 Watt 8 Ohm Presa Cuffia Sul Frontale Regolazioni Alti, Bassi e Bilanciamento PARTE FINALE STACCABILE DA PARTE PRE (Interruttore Posto Sul Pannello Posteriore) Funzione LOUDNESS, Stereo - Mono Filter Low High Ingressi: Phono 1 Phono 2 Tuner Aux Ingressi DIN 5 Poli Uscite Altoparlanti Punto e Linea Caratteristiche Produttore: Power output: 32 watts per channel into 8 (stereo) Frequency response: 10Hz to 70kHz Total harmonic distortion: 0,07% Signal to noise ratio: 77dB (MM), 100dB (line) Dimensions: 320 x 100 x 220mm GARANTISCO OTTIMO IMBALLO A PROVA DI CORRIERE Primo contatto via sms o whatsapp o email. Non rispondo alle chiamate se non ho ricevuto prima un contatto scritto.

HT 2Hertz HT25 Tweeter 25mm Cupola con Magnete al Neodimio 120 Watt nuovi High performance, small size and easy mounting. HT 25 is a Hertz car audio tweeters with neodymium magnet, Tetolon® soft dome and 25mm ø, ferrofluid-cooled mobile voice coil. HT 25 provides a rear acoustic load chamber, to extend the low frequency limits without incurring resonance effects. High energy magnet and accessories for factory location and flush mounting ensure minimum size, providing flexibility and easing installation in whatever car compartments. Perfect for two-way or multi-way systems with unique features. Data table Size mm (in.) 25 (1") Power Handling - Peak W 120 Power Handling - Continuous W 4 Impedance Ω 4 Frequency response Hz 1.6k ÷ 22k Sensitivity dB SPL 92 Voice coil Ø mm (in.) 25 Magnet Neodymium Cone/Dome Tetolon

Subwoofer attivo acoustic research S10H0 bassi mostruosi, caldi e corposi. il subwoofer ideale per il tuo impianto home theatre o in qualsiasi contesto musicale. 150w di potenza effettiva vero gioiello introvabile e made in USA colore nero euro 400 emanuele 335 6777429 spedisco in tutta italia! a 25cm cone type woofer of long stroke type is carried in low-pass. multi-port slot loading method is adopted as enclosure. two kinds of input terminals of high level and low level are carried. variable adjustment function and auto sensing function of input level and crossover frequency are carried. method amplifier built-in • 1 way • 1 speaker • multiport slot loading used unit for low-pass: 25 cm cone type frequency characteristic 35 hz to 200 khz ± 3 db impedance 8 Ω allowable input 150 w (rms) crossover frequency 40 hz to 200 hz (continuously variable) external dimensions width 360 Ãâ€â€ height 350 Ãâ€â€ depth 360 mm weight 14.0 kg

Vendo Amplificatore Car Stereo Harman Kardon CA 260 usato pochissimo. Caratteristiche Tecniche: Power Output, RMS 60 watts per channel into 4 Ohms, 20 - 20,000Hz: 90 watts per channel into 2 Ohms, 20 - 20.000Hz: 180 watts bridged mono into 4 Ohms, 20- 20,000Hz HCC (High Instantaneous Current. +/-30A Capability) THD (4 Ohms/2 Ohms): No more than 0.1 %10.2% Negative Feedback: 25dB Power Bandwidth. 10Hz to 100,000Hz Frequency Response 10Hz to 100,000Hz + 0, - 3dB Signal-to-Noise Ratio: 80dB lnput Sensitivity Line Level: 0.1V10.5V (switchable) High Level: 1V Active Crossover Characteristics High Pass. 200Hz, 12dB/Octave Low Pass: 200Hz, 6dB/Octave Power Supply. DC +13.8V (11 -16V usable), negative ground Typical lnput Current Requirements At Idle. 2.5A Full Power MUSIC Signal 6 7A (4 Ohms/ch.) 10A (2 Ohms/ch.) Full Power Sine Wave. 20A (4 Ohms/ch.) 30A (2 Ohms/ch.) Dimensions (W x H x D). 15-518" x 3-718'' x 7-1/8" (396 x 98 x 180mm) Weight. 1Olbs. 202. 14.6kgl

Satellite Power: 400 W RMS - 800 W max. Nominal impedance: 4 ohm Woofer: 3 x 8" neodymium Tweeter: 12 x 1" Dispersion: 100° x 70° (H x V) (-10 dB) Dimensions: 255 x 695 x 400 mm Net weight: 11.5 kg Subwoofer Power: 700 W RMS - 1400 W max. Nominal impedance: 4 ohm Woofer: 1 x 15" Dimensions: 483 x 725 x 585 mm Net weight: 36.5 kg Satellite + subwoofer Frequency response: 35 - 18,000 Hz SPL max. (@ 1 m): 128 dB Amplification Low stage: 1 x 700 W RMS / 1400 W max. at 4 ohm Mid/high stage: 1 x 400 W RMS / 800 W max at 4 ohm Level: level adjustment on each channel + master Sub: adjustment of the level of the box Inputs CH1: 1 x XLR Combo / line jack / MIC CH2: 1 x XLR / line jack / MIC Combo CH3: 1 x line jack CH4/5: 1 x RCA L/R line + Bluetooth input Input impedances MIC 1/2: balanced 40 kohm Line 1/2: symmetrical 10 kohm Line 3: symmetrical 20 kohm Line 4/5: asymmetrical 5 kohm Outputs 1 x insert on top of the satellite box 1 x XLR MIX OUT balanced for output to another system 2 x XLR LINE OUT symmetrical for repique CH1 and 2 DSP 24 bit (1 in 2 out) EQ / presets / low cut / delay / Bluetooth TWS

Alpine Swd-355 Subwoofer Amplificato In Cassa Da 12" 30cm, 3 mesi di vita praticamente nuovo in garanzia. pagato 280E. vendo a 200E.vendo per cambio impianto audio.Il sub va benissimo e potente. CARATTERISTICHE Componenti SWE-1244E - 12" (30cm) Subwoofer (40hm) MRV-M250: Digital V-POWER Mono Amplifier High Quality Bass Reflex Box 12” (30cm) SWE-1244E Subwoofer 650W Peak Power Handling Heavy Duty Subwoofer Grill Frequency Response: 30Hz - 200Hz MRV-M250 Amplificatore Mono incorporato V-POWER DIGITAL (class-D) 550W Max Power 150W RMS into 4Ohm 14,4V 1%THD Adjustable Low Pass Filter, 50-400Hz 24dB/oct. Variable Bass EQ (fc=50Hz), 0 to +12dB RCA & Speaker Inputs High Quality Bass Reflex Box White Illuminated Alpine Logo (pulsing) Removable Port Plug for Sealed and Vented Operation All Plug Connectors (Easy Removal, no Tools Required) Dimensions: 450mm (W) x 392mm (H) x 315mm / 422mm (D) prezzo non trattabile e' praticamente nuovo, posso includere spese di spedizione. Preferibile ritiro a mano e constatazione del funzionamento che spara dei mega bassi.